| Blue Marble® 2-Cycle oil delivers more horsepower, more fuel efficiency and more cleanliness than any leading brand of 2-cycle oil on the market. Blue Marble® Oil incorporates patented technologies that make traditional approaches to lubrication obsolete! Old line two-cycle oils employ hydrocarbons to provide lubrication. Blue Marble® changes the metal surface. Imagine what it would cost to have a ceramic coating that never deteriorated. At a microscopic level, the metal surface of engine parts is changed and friction is reduced dramatically to increase performance, fuel efficiency and clean burning. Increases Fuel Efficiency - Blue Marble® 2-Cycle Oil provides increased fuel efficiency. A combination of reduced friction and more efficient combustion improve the efficiency of two-cycle engines. Generates More Power - Use of Blue Marble® 2-Cycle Oil has demonstrated power (rpm) gains. This increased horsepower doesn't require any engine modifications - just use Blue Marble® - one of the least expensive ways to increase power. Provides for a Safer Environment - Our technology uses a mineral oil that naturally biodegrades. The mineral oil base in Blue Marble® also has no aromatics so there is no sheen on the water and smoke is reduced significantly.
| |
 |
| • |
Blue Marble®
High Performance 2-Cycle Oil: |
| |
| o |
Blue Marble® 2-Cycle
Oil is an ashless, high detergent, top-quality lubricant
that meets the needs of all high performance 2-cycle engines
whether air or water cooled as a premix or oil injected.
Blue Marble® 2-Cycle Oil is made from a highly
refined mineral oil, which is inherently biodegradable, and
contains our proprietary patented technology. |
| o |
Blue Marble® formula
improves overall engine performance and reduces friction and
smoke. |
| o |
Meets or exceeds JASO FD, TC-W3®
and ISO EGD specifications. |
| o |
U.S. Patents: 5310419, 5540788;
Patents Pending.
|
|
| • |
Usage info: |
| |
| o |
Recommended for use in 2-cycle
engines in fuel injections or premix: ATVs, motorcycles,
outboard motors, personal watercrafts, scooters, snowmobiles
and other 2-cycle engines. |
| o |
Safe for use in all power valve
systems.
|
| o |
Follow engine manufacturer’s mix
recommendation. Upon first use, run at moderate RPMs for
first 20 minutes. Run at normal RPMs.
|
|
| |
Technical Data:
(typical properties not to be considered specifications)
| Appearance (color) |
Clear, dark green |
| Pour Point |
< -40° F |
| Flash Point |
184° F |
| Kinematic Viscosity @ 40° C |
38.5 |
| Kinematic Viscosity @ 100° C |
7.5 |
| Viscosity Index |
160 |
|
| |
Tips and Tricks:
When Blue Marble® patented technology is introduced
to a combustion engine, a “greening process” occurs as explained
in our technology page of our website. This process begins when
the metal is introduced to our technology and ends at the time
of full surface conversion. This window of time varies from
engine to engine depending on the dilution of fuel/oil ratio and
the air/fuel-oil ratio. We have developed a process to speed up
the Blue Marble® surface conversion as outlined
below. This technique is optimal for racers and tuners for quick
HP gains while still protecting the engine. Complications
may occur if you are not qualified to perform these technical
instructions.
1. Remove spark plugs. 2. Bring “one” piston to TDC (verify TDC
through the use of a non-metallic tool such as a pencil). 3.
Pour in specified amount of 2-Cycle Oil through spark plug hole
and let sit for 2 minutes. 4. Very slowly turn the engine over 5
revolutions to allow coating of internal parts with Blue Marble®
Oil. 5. Move on to the next piston/pistons and, one-by-one,
perform the same procedure until all pistons are coated. 6. Let
sit for at least 24 to 72 hours. 7. Repeat steps Four through
Six. 8. Install spark plugs. 9. Run engine. (increased smoke
will be expected for several minutes)
*Recommended treatment. Damage could occur to engine if
more than specified amount is added.
| Piston or Bore size in millimeters |
Amount Added Blue® Marble High Performance
2-Cycle Oil |
| Under 50mm |
1/2 oz. |
| Between 50mm to 60mm |
1 oz. |
| Between 60mm to 70mm |
1 & 1/2 oz. |
| Between 70mm to 85mm |
2 oz. |
| Between 85mm to 100mm |
2 & 1/2 oz. |
| Over 100mm |
3 oz. |
|
|
|
| |
